A Survey of the Parameters of the Friction Stir Welding Process of Aluminum Alloys 6xxx Series
DOI:
https://doi.org/10.18034/ei.v9i1.548Keywords:
Friction stir welding, welding process, aluminum alloys, mechanical propertiesAbstract
Friction stir welding is a modern innovation in the welding processes technology, there are several ways in which this technology has to be investigated in order to refine and make it economically responsible. Aluminum alloys have strong mechanical properties when they are welded by using the Friction Stir welding. Therefore, certain parameters of the welding process need to be examined to achieve the required mechanical properties. In this project, a literature survey has been performed about the friction stir welding process and its parameters for 6xxx series aluminum alloys.
Downloads
References
Bayazid, S. M., Farhangi, H., Ghahramani, A. (2015). Investigation of Friction Stir Welding Parameters of 6063-7075 Aluminum Alloys by Taguchi Method. Procedia Materials Science, 11, 6-11.
Dawes, C. J. and Thomas, W. M. (1996). Friction stir process Welds Aluminum alloys. Welding Technology, 4, 41-45
Elanchezhian, C., Vijaya Ramnath, B., Venkatesan, P., Sathish, S., Vignesh, T., Siddharth, R. V., Vinay, B., Gopinath, K. (2014). Parameter Optimization of Friction Stir welding of AA8011-6062 Using Mathematical Method. Procedia Engineering, 97, 775-782.
Elangovan, K., Balasubramanian, V., and Babu, S. (2009). Predicting tensile strength of friction stir welded AA6061 aluminium alloy joints by a mathematical model. Materials and Design, 30, 188-193.
Fu B., Qin, G., Li, F., Meng, X., Zhang, J., Wu, C. (2015). Friction stir welding process of dissimilar metals of 6061-T6 aluminum alloy to AZ31B magnesium alloy. Journal of Materials Processing Technology, 218, 38-47.
Jayaraman, P., Mahesh Kumar, L. (2014). Multiresponse Optimization of Machining Parameters of Turning AA6063 T6 Aluminium Alloy using Grey Relational Analysis in Taguchi Method. Procedia Engineering, 97, 197-204.
Joyson Abraham, S., Chandra Rao Madane, S., Dinaharan, I., John Baruch, L. (2016). Development of quartz particulate reinforced AA6063 aluminum matrix composites via friction stir processing. Journal of Asian Ceramic Societies, 4(4), 381-389.
Karthikeyan, L., & Senthil Kumar, V. S. (2011). Relationship between Process Parameters and Mechanical Properties of Friction Stir Processed AA6063-T6 Aluminum Alloy. Materials and Design, 32, 3085-3091
Lakshminarayanan A. K. & Balasubramanian V. (2008). Process parameters optimization for friction stir welding of RDE-40 aluminium alloy using Taguchi technique. Transactions of Nonferrous Metals Society of China, 18, 548-554.
Liu, Huijie, & Fuji, H. (2003). Mechanical properties of friction stir welded joints of 6060- H24 aluminium alloy. Science and technology of welding and joining, 8, 50- 54.
Mandal, N. R. (2005). Aluminium Welding. Narosa Publishing House, Second edition, New Delhi.
Minton, T. and Mynors, D. J. (2006). Utilization of engineering workshop equipment for friction stir welding. Journals of Materials processing Technology, 177, 336- 339.
Ouyang, J. H., Kovacevic, R. (2002). Material flows during friction stir welding (FSW) of the same and dissimilar aluminium alloy. Material Engineering Performance, 11(1), 51-63.
Sharma, H. K., Bhatt, K., Shah, K., Joshi, U. (2016). Experimental Analysis of Friction Stir Welding of Dissimilar Alloys AA6061 and Mg AZ31Using Circular Butt Joint Geometry. Procedia Technology, 23, 566-572.
Thomas, W. M., Nicholas E. D. (1997). Friction stir welding for the Transportation in industries. Material & Design, 18(4-6), 269-273.
--0--
Downloads
Published
Issue
Section
License
Engineering International is licensed under a Creative Commons Attribution-Noncommercial 4.0 International License (CC-BY-NC). Articles can be read and shared for noncommercial purposes under the following conditions:
- BY: Attribution must be given to the original source (Attribution)
- NC: Works may not be used for commercial purposes (Noncommercial)
